Tag: PRV

Author: Atul Singla | Piping Engineering Expert | Updated: May 2026 Pressure Relief Valve (PRV): Definition, Types, Working, Sizing, Codes and Standards In my 20+ years of piping engineering experience across EPC and site projects, I’ve seen one component repeatedly making the difference between safe operation and catastrophic failure — the Pressure Relief Valve (PRV). Whether it’s a refinery flare system or a compressor discharge line, a wrongly selected or poorly located PRV can lead to severe safety incidents, equipment damage, or even shutdowns. In this detailed guide, I’ll walk you through the working, types, sizing, location guidelines, and applicable codes for Pressure Relief Valves — not just theoretically, but with practical insights from real field challenges I’ve personally encountered. ✅ Key Takeaways Pressure Relief Valves (PRVs) protect equipment from overpressure conditions. Proper selection depends on backpressure, service type, and system design. Incorrect sizing is one of the most common causes of PRV failure. Standards like API 520, API 521, and ASME Section VIII govern PRV design. Improper installation location can delay pressure relief and create hazards. A Pressure Relief Valve (PRV) is a safety device designed to automatically release excess pressure from a system when it exceeds a preset limit, preventing equipment failure. It operates by opening at a specific pressure and closing once normal conditions are restored, ensuring safe operation of piping systems and pressure vessels. Interactive Engineering Quiz Q1: In a high backpressure compressor discharge system, which Pressure Relief Valve (PRV) type is most suitable? Conventional PRV Balanced Bellows PRV Temperature actuated valve ✅ Correct Answer: Balanced Bellows PRV Explanation: In systems with high built-up backpressure, conventional PRVs fail due to spring interference. API 520 recommends balanced bellows valves for such conditions. Q2: What is the maximum allowable pressure accumulation over MAWP during relief (as per ASME)? 5% 8% 10% ✅ Correct Answer: 10% Explanation: As per ASME Section VIII, accumulation shall not exceed 10% for most pressure vessels. Q3: What is the primary cause of Pressure Relief Valve chattering? Oversized PRV Low inlet temperature Incorrect flange rating ✅ Correct Answer: Oversized PRV Explanation: Oversized valves open/close rapidly due to unstable flow conditions, leading to chattering and seat damage per API 521 guidance. Previous Next Pressure Relief Valve (PRV): Engineering Fundamentals, Relief Scenarios & System Design What are Relief Events in Pressure Relief Valve (PRV) Design? In my field experience across refinery and steel plant projects (similar to JSPL environments), the most critical aspect often overlooked is identifying the correct relief event. A Pressure Relief Valve (PRV) is only as reliable as the scenario it is designed for. Blocked outlet condition Thermal expansion in liquid-filled systems External fire exposure (fire case) Control valve failure (fail-open) Utility failure (cooling water loss) ⚠️ Field Warning: In one EPC project, incorrect fire-case load estimation resulted in undersized PRVs — leading to flare system overload during commissioning. Potential Lines of Defense Against Relief Events Relief valves are the last line of defense. Before relying on PRVs, engineering design includes multiple protective layers: Process control systems (DCS/PLC) Alarm systems (operator response) Shutdown systems (ESD) Pressure Relief Systems (PRV/PSV) What is a Pressure Relief System? A relief system is not just a valve — it includes inlet piping, PRV, outlet piping, discharge headers, and flare systems. Design must comply with API 521. Why Use a Relief System? Prevent explosion due to overpressure Protect costly equipment Ensure regulatory compliance Code Requirements for PRV Design PRV design shall follow ASME Section VIII along with API 520. Pressure Accumulation Limits Single PRV: Max 10% of MAWP Multiple PRVs: Up to 16% allowed Fire case: Up to 21% allowed Locating Pressure Relief Valves (PRV) Improper location is one of the most common mistakes I’ve seen during site audits. The PRV must be installed: Directly on top of pressure vessel nozzle As close as possible to protected equipment Without isolation valves (unless approved) Types of Pressure Relief Valves (PRV) Based on system design and operating conditions, PRVs are classified into: Conventional PRV Balanced Bellows PRV Pilot-Operated PRV Power Actuated PRV Conventional Pressure Relief Valve Most commonly used PRV, suitable for low backpressure applications. Advantages Simple design Low cost Disadvantages Affected by backpressure Working of a Pressure Relief Valve (PRV) PRV operates using spring force balancing system pressure. When pressure exceeds set limit, valve lifts and discharges fluid. Pressure Relief Valve (PRV): Engineering Data & Code Standards Table Parameter Value / Requirement Standard Max Accumulation 10% ASME Section VIII Backpressure Limit Typically <10% for conventional valves API 520 Sizing Criteria Mass flow & relieving conditions API 520 Relief System Design Flare, headers, knockout drum API 521 Valve Dimensions Standard orifice sizes API 526 Pressure Relief Valve (PRV): Field Application & Lessons Learned Field Case Study: Real-World Application Problem: During a steel plant expansion project (similar to JSPL-type configuration), a compressor discharge system experienced frequent Pressure Relief Valve (PRV) failures. The installed valve was a conventional PRV, while the system had significant built-up backpressure due to a long flare header. Result: Continuous chattering, seat damage, and repeated shutdowns. ✅ Solution & Outcome: We replaced the conventional valve with a balanced bellows type PRV as recommended in https://www.api.org/products-and-services/standards/important-standards-announcements/api-520API 520. Additionally, inlet piping was optimized to reduce pressure drop. ✅ Result: Zero chattering, stable operation, and improved plant reliability. Engineering Recommendation: Always evaluate backpressure and dynamic flow conditions during PRV selection. Never rely solely on datasheets — simulate real operating scenarios wherever possible. Pressure Relief Valve Sizing Basics PRV sizing is governed by relieving flow rates and thermodynamic properties. As per https://www.api.org/products-and-services/standards/important-standards-announcements/api-520API 520, the general sizing equation for gas/vapor service is: A = (W × √T) / (C × Kd × Kb × Kc × P) A = Required orifice area W = Mass flow rate T = Relieving temperature P = Set pressure K factors = Correction factors ⚠️ Critical Mistake: Many engineers ignore inlet pressure drop. As per API guidelines, it must not exceed 3% of set pressure. Relief Valve Chattering – Causes & Prevention Oversized PRV High built-up backpressure Improper spring selection Poor inlet piping design Chattering drastically reduces valve life and can lead to catastrophic seat leakage. Difference Between PSV and PRV Parameter PRV PSV Function Gradual opening Pop action (instant) Application Liquids & gases Gases/steam Operation Modulating Snap acting Frequently Asked Engineering Questions What is the difference between set pressure and relieving pressure? Set pressure is the point at which the PRV opens, while relieving pressure includes accumulation above set pressure. Limits are defined in https://www.asme.org/codes-standards/find-codes-standards/bpv-codeASME Section VIII. Why is backpressure critical in PRV selection? High backpressure affects valve lift and capacity. Balanced bellows valves are recommended as per https://www.api.org/products-and-services/standards/important-standards-announcements/api-520API 520. What causes PRV failure most often? Incorrect sizing, poor maintenance, and installation errors are primary causes. Guidelines are covered in https://www.api.org/products-and-services/standards/important-standards-announcements/api-521API 521. Can a PRV be installed with an isolation valve? Generally not allowed unless specific conditions are met with interlocks as per https://www.asme.org/codes-standards/find-codes-standards/bpv-codeASME guidelines. What is PRV accumulation for fire case? Accumulation can go up to 21% during fire exposure conditions as permitted in https://www.api.org/products-and-services/standards/important-standards-announcements/api-521API 521. When should pilot-operated PRVs be used? These are preferred in high-pressure systems requiring tight sealing and minimal leakage. Design guidance is available in https://www.api.org/products-and-services/standards/important-standards-announcements/api-520API 520.